Suomy Mr Jump Jackpot - Black

Stock Code: SU/MR-JA-BLK-XS

RRP: £256.50

Out Of Stock


Mr Jump

MR. JUMP, the fiber helmet studied in details for comfort, technology and for sure safety for end user. It has been studied and tested to optimize the outside and inside air flows.

SizesOpen or Close
XS53/546 1/2” - 6 5/8”
S55/566 3/4” – 6 7/8”
M57/587” – 7 1/8”
L59/607 1/4” – 7 3/8”
XL61/627 1/2” – 7 5/8”
XXL63/647 3/4” – 7 7/8”


helmet must fit tightlyTo have a maximum safety the helmet must fit tightly and be correctly and securely fastened, in order not to be able to be taken off neither by pulling it nor by rotating it around the head.
If it is too big, it may slide down over the eyes or turn in a lateral direction due to movement during riding, blocking the right visibility. 
OUTER SHELL in tricarboco material, mix of Kevlar, carbon and fibre, joint through resin hand made using new technologies, which foresee aramidic resins.
INTERNAL POLYSTYRENE protective lining, available in three sizes (S, M and L). The special shape and construction in different density increases mechanical resistance in the event of accidental shock. Inner channels studied in the wind tunnel guarantee a perfect ventilation. 

D-RING RETENTION SYSTEMThe D-RING RETENTION SYSTEM has been designed and patented by Suomy. 
Insert the free side of the strap in the rings. Pull the end until the strap presses firmly against the jaw. 
After this operation, it should not be possible to remove the helmet. Verify that by grabbing it from the back and rotating it to the front it cannot be removed and it is fixed to the head. If the helmet tends to come off or rotates freely, tighten the strap again until the right pressure is obtained and repeat test.
If after repeating the test you are not able to efficiently tighten the retention system, do not use the helmet. Only after checking the correct tension of the strap, fix the free end locking it with the automatic stud to the release tab.
The automatic stud is necessary only to fix the free end of the strap to prevent it from flapping while riding. Fixing the release button does not assure that the helmet is correctly in position and properly fastened: the correct locking of the strap must be verified exclusively following the above paragraphs.
To release the retention system, release the automatic stud button and pull the release tab to loosen the closure. Slide out the free end of the strap from the «D Rings». Use the release tab only to remove the helmet! Never release this tab while riding.


MRJUMP is homologated as per the following rules:

ECE 22-05Europe
DOTAmerica and Canada
INMETRO NBR 7471Brasil

You have to refer always to the homologation of the country in which the helmet is sold.

Internal comfort

Internal comfortCHEEK PADS completely removable and washable, with different thickness to get a perfect customization od the helmet.

INTERNAL SHELL completely removable and washable, in different thicknesses for a complete customization of the product. 
The internal removable shell has been studied for an uniform stand on the head. The visible channels allow the air flow to check the temperature in the internal part of the helmet and to let off the hot air through the back part. 

INNER (cheek pads and inner liner) are completely in fabric COOLMAX® ACTIVE with treatment INTERPOWER:
  • Wicks sweat away from the body.
  • Keeps the user fresh, dry and comfortable.
  • Lightweight, soft and breathable fabric.
  • Performance verified and certified by ADVANSA.


XS53/546 1/2” - 6 5/8”
S55/566 3/4” – 6 7/8”
M57/587” – 7 1/8”
L59/607 1/4” – 7 3/8”
XL61/627 1/2” – 7 5/8”
XXL63/647 3/4” – 7 7/8”


The SHELL is in polystyrene with channels for air flows.
In the front part there are upper and back air ventilations, which help the internal helmet ventilation.
On the CHIN GUARD there is an air ventilation for the front ventilation.


PEAKThe OUTER SHELL has ribs to channel better the air flows.

The PEAK has an aereodynamic impact. 
The wide open spac

Spare Parts

Spare Parts

Inner Covered Chin Guard KAMJ0M00
Chin Guard Air VentWhiteKAMJVM01
Screw Kit KAMJVF00
Inner Comfort Liner
removable and washble
Size SKAMJ0I02
Size MKAMJ0I03
Size LKAMJ0I04
Cheek PadsSize XSKAMJ0L01
Size SKAMJ0L02
Size MKAMJ0L03
Size LKAMJ0L04
PeakAvailable for each graphic

We have placed cookies on your device to help make this website better.